Cynergy3, 0.9 L/min Flow Controller, Cable, Relay

  • RS Stock No. 338-9823
  • Mfr. Part No. FS15LF
  • Manufacturer Cynergy3
Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
COO (Country of Origin): GB
Product Details

Normally Open Flow Switch

Flow switch series from Cynergy3. These flow switches are reed switch based and can monitor the flow of liquids up to 10bar in pressure. This series of flow switches can be mounted horizontally or vertically and have minimal flow restriction. Flow switches are ideally used in water but can be used in weak acidic liquids.

Mainly for use with hot or cold water, however they may also be used with a wide range of chemicals
Pressure rating 150psi maximum
Switching current 1A dc or ac (rms)
Switching voltage 240V dc or ac (rms)
Switching power 15W (15VA) resistive loads
Operating temperature 85°C maximum
Vertical or horizontal mounting
Standard compression or push fit fittings
WRAS approved for use in cold water
Complete with a 250mm lead

Note

Not to be used in any chlorinated liquids

//media.rs-online.com/t_line/LF338982-10.gif

Cynergy3 Flow Detection Switch

The Cynergy3 flow detection switch has a maximum flow rate of 0.90L/min designed for use in liquid flow systems at pressures up to 10bar and temperatures up to 85°C. Its design is based around a moving magnet and a fixed reed switch with a low flow restriction. This switch is designed to be used in liquids only and should not be used in systems with significant amounts of solid particles. This flow switch can be mounted horizontally or vertically and has minimal flow restriction. It is ideally used in water but can be used in weak acidic liquids.
Note:
Not to be used in any chlorinated liquids

Features and Benefits

• 15mm and 22mm tube versions
• Low flow version available in a 15mm tube
• Release flow rate is 0.25L/min
• Use in cold and hot water up to 85°C
• Mainly for use with hot or cold water however, they may also be used with a wide range of chemicals
• Pressure rating is 150psi maximum
• Switching current is 1A DC or AC (rms)
• Switching voltage is 240V DC or AC (rms)
• Switching power is 15W (15VA) resistive loads

Applications

• Flow measurement and dosing control
• Industrial use

Certifications

• WRAS approved

Specifications
Attribute Value
Maximum Flow Rate 0.9 L/min
Electrical Connection Cable
Control Output Relay
Pipe Diameter Range 15 mm
Maximum Operating Temperature +85°C
9 : Next working day
7 Within 5 working day(s) (Global stock)
Price (ex. GST) Each
$ 48.26
(exc. GST)
$ 55.50
(inc. GST)
units
Per unit
1 - 5
$48.26
6 - 11
$46.33
12 +
$45.90
Related Products
Working on the calorimetric principle these sensors have ...
Description:
Working on the calorimetric principle these sensors have a working range of 1 to 10m/sec (air velocity) and can be set to give an output signal should the airflow drop below the preset level. Suitable for monitoring in HVAC applicationsLED ...
Series IR Precision Regulators are designed to be ...
Description:
Series IR Precision Regulators are designed to be compact and light weight. The maximum set pressure has been expanded from the conventional 0.7MPa to 0.8MPa. Relief flow has been increased by nearly 5 times (compared to SMC IR201, IR401).
Suitable for flow measurement & ON/OFF control applications ...
Description:
Suitable for flow measurement & ON/OFF control applications with process fluids, pump protection, cooling/heating circuits and lubrication. Interfaces via S030 pipework flow adaptor (see stock no. 249-7513 typically)Large LCD display of flow rate with bargraph. Simulation function, LED status indication. ...
Ultra Compact, intelligent sensors featuring MEMS technology for ...
Description:
Ultra Compact, intelligent sensors featuring MEMS technology for precision mass airflow. Precision unidirectional mass airflow up to 3 LPMStable output across full scale. Ultra-compact size 36.6 (D) x 8 (W) x 16.8 (H) mm. Low power consumption. Joint type Bamboo ...