Magnatec L298N, Brushed Motor Driver IC, 46 V 4A 15-Pin, MULTIWATT V

  • RS Stock No. 636-384
  • Mfr. Part No. L298N
  • Manufacturer Magnatec
Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

L298 Dual Full Bridge Motor Driver

ST Microelectronics presents its L298 dual full bridge driver series. The L298 series from ST is an integrated high voltage, high current dual full bridge driver. These devices are specially designed to accept standard TTL logic and drive inductive loads in Relays, Solenoids, DC and Stepper Motors. Featured are two enable inputs that allow the L298 to be enabled or disabled independently of the input signals. The emitters of the lower transistors of each bridge are connected together, the corresponding external terminal can be used to connect an external sensing resistor. In addition, a supply input is provided so that the logic works at a lower voltage.


  • Operating supply voltage up to 46 V

  • Total DC current of up to 4 A

  • Low saturation voltage

  • Over-temperature protection

  • Logical "0" input voltage up to 1.5 V (high noise immunity)

What are Motor Driver IC's?

Motor Driver ICs are current amplifiers and are an essential component of motor interfacing. The motor driver integrated circuit chip acts as the interface between a microprocessor or microcontroller, and a motor. As microprocessors tend to operate at lower currents, and motors at higher, motor driver ICs are needed to supply current to the motor as needed. The RS Components range of Motor Driver ICs includes models from leading brands, in various types and configurations to support your design needs.

Motor Controllers & Drivers, STMicroelectronics

Attribute Value
Motor Type Brushed DC
Output Configuration Dual Full Bridge
Maximum IGBT Collector Current 4A
Maximum Collector Emitter Voltage 46 V
Mounting Type Through Hole
Package Type MULTIWATT V
Pin Count 15
Maximum Operating Supply Voltage 46 V
Minimum Operating Supply Voltage 4.8 V
Length 19.6mm
Width 5mm
Height 10.7mm
Minimum Operating Temperature -25 °C
Dimensions 19.6 x 5 x 10.7mm
Maximum Operating Temperature +130 °C
24 : Next working day
269 Within 5 working day(s) (Global stock)
Price (ex. GST) Each
$ 8.45
(exc. GST)
$ 9.72
(inc. GST)
Per unit
1 - 9
10 +
Packaging Options:
Related Products
Floating Channel for Bootstrap Operation to +600V4.5A Sourcing ...
Floating Channel for Bootstrap Operation to +600V4.5A Sourcing and 4.5A Sinking Current Driving Capability. Common-Mode dV/dt Noise Cancelling Circuit. Built-in Under-Voltage Lockout for Both Channels. Matched Propagation Delay for Both Channels3.3V and 5V Input Logic Compatible. Output In-phase with Input. ...
Dual Drivers with Enable Inputs+4V to +14V Single ...
Dual Drivers with Enable Inputs+4V to +14V Single Power-Supply Range4A Peak Sink/Source Current. Inputs Rated to +14V, Regardless of VDD Voltage. Low 12ns Propagation Delay6ns Typical Rise and 5ns Typical Fall Times with 1nF Load. Matched Delays Between Channels. Parallel ...
The Control Integrated Power System (CIPOS) are families ...
The Control Integrated Power System (CIPOS) are families of highly integrated, compact power modules. They are designed to drive motors in home appliances, fan and pump applications. These energy-efficient Intelligent Power Modules (IPM) deliver increased power density with enhanced system ...
The reversible motor driver for output 1.0A for ...
The reversible motor driver for output 1.0A for 1 motor can set the output modes to four modes, normal, reverse, stop(idling), and braking in accordance with logic input (2 inputs). Built-in surge absorption diode. By built-in power save circuit, current ...