Martindale PD690 Voltage Indicator Proving Unit 700V

  • RS Stock No. 719-0894
  • Mfr. Part No. RSPD690
  • Manufacturer Martindale
Technical data sheets
Legislation and Compliance
RoHS Status: Not Applicable
COO (Country of Origin): PH
Product Details

Filament Test Lamps Drummond MTL7 and MTL9C

Two filament test lamps giving safe indication of voltages between 150V and 500Vac/dc. Their robust design meets the recommendations of the Health and Safety Executive in their guidance notes on electricians test lamps (GS38)

MTL 7

The lamp housing, moulded in hard rubber, contains the 15W rough service SES pygmy lamp. Both the lamp housing and the probe contain a 500mA HRC fuse, have a finger shield and removable insulated probe tip with only 2mm of exposed metal. The probe handle contains a 4000Ω series resistor. A two layer double insulated cable with white inner insulation gives a clear warning of abrasion that might compromise the users safety, and is resistant against flame, heat and oil. To enable use in most circumstances a right angled probe tip is supplied in addition to the two straight tips. For convenience a small pouch is attached to the cable for storage of the probe tips.

MTL9C Additional Features

The MTL9C incorporates a test circuit, totally enclosed in a small moulded case and mounted on the cable. This continuity tester indicates continuity in the test lamp circuit and thus warns of fault conditions such as a blown fuse or broken filament lamp, (this test ignores the presence of the LED circuit).

Caution

Test lamps should be proved safe before and after use, by testing on a known live circuit, using the continuity tester, or through the Martindale PD690 proving unit.

Martindale Proving Units

The Martindale proving unit has an output voltage rating of 700VAC. It is compatible with voltage indicators, including the new VI-15000 and VI13800.

Features and Benefits

• Calibrated by RS
• Designed for use with Drummond and other similar lower resistance test lamps, having sufficient output to cause illumination
• Neon indicates battery condition
• Long battery life time with a low battery indicator
• Single probe operation allows for non-contact voltage tester proving (access 5mm)
• Operates test voltage indicators that have greater than 4kohm internal resistance
• Battery of6xLR6/MN1500 1.5V alkaline batteries or equivalent
• Operating temperature ranges between -10°C and 40°C

Applications


Digital multimeters
• Clamp meters
• Electrical testers

Mains Voltage Indicators - Contact

Specifications
Attribute Value
Output Voltage 700V
Battery Type AA
Power Source Battery
Dimensions 143 x 84 x 50mm
Weight 400g
Height 50mm
Length 143mm
Maximum Operating Temperature +40°C
Minimum Operating Temperature -10°C
Model Number p PD690
Width 84mm
1 : Next working day
123 Within 5 working day(s) (Global stock)
Price (ex. GST) Each
$ 260.78
(exc. GST)
$ 299.90
(inc. GST)
units
Per unit
1 +
$260.78
Related Products
The Volt Stick PRO is a pen style ...
Description:
The Volt Stick PRO is a pen style non-contact voltage detector from our high quality RS PRO brand. Able to safely check the presence of an AC voltage within cables, wall sockets and fuses junction boxes, conveniently no current flow ...
RS Pro VP-3 Volt Stick is a pen ...
Description:
RS Pro VP-3 Volt Stick is a pen style non-contact AC voltage indicator. Safely checks the presence of an AC voltage in cables, wall sockets, fuses and junction boxes. No current flow is needed for correct operation. An essential tool ...
Safely detect the presence of AC voltage in ...
Description:
Safely detect the presence of AC voltage in cables, wires, wall sockets fuses and junction boxes with the RS PRO VP-4. Ergonomically designed for comfort, it features a built in torch for confined spaces, a clip for pockets or tool ...
The Non-Contact Volt. Stick® is a tester for ...
Description:
The Non-Contact Volt. Stick® is a tester for safely checking the presence of an AC voltage without making any disconnections in cables, wall sockets, fuses, circuit breakers, junction boxes etc. No current flow is needed for correct detection. Apply the ...