Testec SI Series TT-SI 9010 Oscilloscope Probe, Active, Differential Type, 70MHz, 1:100, 1:1000, BNC Connector

RS Stock No.:: 512-6078
Mfr. Part No.:: TT-SI 9010
Brand:: Testec

Testec SI Series TT-SI 9010 Oscilloscope Probe, Active, Differential Type, 70MHz, 1:100, 1:1000, BNC Connector

This image is representative of the product range

Unavailable

RS will no longer stock this product.

Alternative

This product is not currently available. Here is our alternative recommendation.

Pico Technology TA Series TA044 Oscilloscope Probe, Differential Type, 70MHz, 1:100, 1:1000, BNC Connector

RS Stock No.: 898-6750

Each

$1,888.26

(exc. GST)

$2,171.50

(inc. GST)

RS Stock No.:: 512-6078
Mfr. Part No.:: TT-SI 9010
Brand:: Testec

Specifications

Technical data sheets

Legislation and Compliance

Product Details

Find similar products by selecting one or more attributes.

Select all	Attribute	Value
	Brand	Testec
	Probe Type	Active, Differential
	Attenuation	1:100, 1:1000
	Bandwidth	70MHz
	Maximum Common Mode Input Voltage	5kV
	Connector Type	BNC
	Model Number p	TT-SI 9010
	Number of Probes	1
	Series	SI
	Safety Category	CAT I 2500 V, CAT II 7000V
	Rise Time	5ns

	Select all
	Brand Testec
	Probe Type Active, Differential
	Attenuation 1:100, 1:1000
	Bandwidth 70MHz
	Maximum Common Mode Input Voltage 5kV
	Connector Type BNC
	Model Number p TT-SI 9010
	Number of Probes 1
	Series SI
	Safety Category CAT I 2500 V, CAT II 7000V
	Rise Time 5ns

RoHS Status: Not Applicable

COO (Country of Origin):: TW

Testec 70MHz Active Differential Oscilloscope Probes

The Testec is an active differential oscilloscope probe that enables a conventional oscilloscope to display and measure in-circuit waveforms that are referenced to high common-mode voltages. It is capable of safely measuring differential voltages up to ±2500V AC and 7000V ac/dc. It supports bandwidths up to 70MHz.

This oscilloscope probe can measure signals below 700V by selecting the attenuation ration to 1:100.

Features and Benefits

Bandwidth is DC to 70MHz
Attenuation is 1:100/1:1000
Rise time is 5ns
Differential mode input voltage is 1:100 ±700V (DC+peak AC) or 700Vrms 1:1000 ±7000V (DC+peak AC) or 5000Vrms
Input impedance is 10Mohm ll10pF each side to ground
Common mode voltage range is 1:100 and 1:1000 ±7000V (DC+peak AC) or 2500Vrms
Non-destructive max. input voltage is 1:100 and 1:1000 ±7000V (DC+peak AC) or 2500Vrms
CMRR (typical) is -80dB at 50Hz and -60dB at 20kHz
Offset (typical) is <±5mV
Noise (typical) is 0.9mVRMS

Applications

Oscilloscope probes are used with oscilloscopes to enable the signals on the circuits being tested to be connected to the oscilloscope so that signals can be measured. These oscilloscope probes can be found in:

Performance conversion
Inverters
Motor speed indicators
Switch mode power supplies

Certifications

CAT I 2500 VAC
CAT II 7000 VAC/DC

Supplied with

Probe
4 x AA batteries
2 x Grabbers red & black
Instruction manual
Factory calibration certificate